
Key takeaways
Treatment controls reflections inside the room. It won't block the neighbor's TV, which needs mass, sealed gaps and decoupling.
Start at the mic. Absorb the reflection points on the side walls and the wall behind the talker, then add corner bass traps if the low end sounds boomy.
Thin foam works only on high frequencies. Sound on Sound says 2-inch foam does a decent job above roughly 2 to 3 kHz and 4-inch foam above about 1 kHz, and neither touches the bass.
DIY panels from 2 to 4 inches of rigid mineral wool or fiberglass, wrapped in breathable fabric, cost far less than most kits.
Fix noise at the source. Switch off the fan, move the computer and get the mic closer instead of raising the gain.
If you only need the basics of choosing a room and setting up a mic, start with our guide to [prepping a room for recording](/posts/how-to-prep-a-room-for-recording). This one goes further into the acoustics.
What goes wrong in a small room
Small rooms cause four recording problems, and each has a different fix.
Problem | What you hear | Fix |
|---|---|---|
Flutter echo | A fast buzz or ring after a clap | Absorb or diffuse one of the two parallel surfaces |
Early reflections | A hollow, boxy sound behind the voice | Absorbers at the reflection points on the side walls and behind the talker |
Room modes | Boomy or uneven low end | Thick bass traps in the corners |
Noise floor | Hiss, fans, hum and traffic | Switch off or move the source and get closer to the mic |
Two details help you prioritize. In a voice recording the mic is close, so early reflections and low-mid buildup matter more than deep bass. And software can't repair either problem afterward. EQ and noise tools can't remove a reflection that's baked into the take.
Step 1: Test the room before you buy anything
You need two tests, and both are free.
1. The clap test. Clap once at your mic position and listen to the tail. A quick buzz or ring points to flutter echo between hard parallel surfaces. Try a few spots. Because a clap is mostly high frequencies, it says nothing about bass trouble.
2. The voice test. Record about 30 seconds of normal speech at your real mic position and listen on headphones. A hollow, roomy quality behind your voice means reflections are reaching the mic.
Save both recordings so you can compare them after each change.
For numbers, the free Room EQ Wizard software (REW) measures decay time with a calibrated measurement microphone such as the miniDSP UMIK-1. Measure at head height in a few positions and average them. Look at the shape of the result more than any single number. A tall spike in the low end points to bass traps, and a long even tail across the mids and highs points to broadband panels.
Don't chase a precise RT60, which is the time a sound takes to fade by 60 dB. There's no agreed target for a voice room. REW's own help says the figure isn't reliable below a few hundred hertz in a home. Phone apps use uncalibrated mics, so use them only for rough before-and-after comparisons.
Step 2: Pick the recording position
Keep the mic away from the exact center of the room, out of the corners and away from the parallel walls.
Face a treated or well-furnished side and put absorption behind the mic. A cardioid mic rejects sound from behind it, so aim its back at the computer or the air conditioner.
Get close. Gain raises the noise floor as much as it raises your voice.
In an untreated room, a cardioid dynamic mic is usually more forgiving than a condenser because it picks up less of the room. Opinions differ, so test both if you own both.
Step 3: Absorb the early reflections
Early reflections arrive within about 25 to 30 milliseconds of the direct sound and cause the boxy tone and comb filtering.
1. Sit at the mic position while a helper slides a mirror along each side wall. Any spot where the mirror shows the mic sends sound straight back to it.
2. Mark those spots on both side walls and the ceiling above the mic.
3. Put 2-inch absorbers on the side-wall marks and behind the talker. GIK Acoustics calls 2 inches the practical minimum for taming the midrange in speech.
4. Re-run the voice test.
Use thicker panels where you can. A 4-inch panel reaches lower, and an air gap of 1 to 4 inches behind a 2-inch panel improves low-frequency absorption too.
Step 4: Trap the bass
Room modes are resonances set by the room's dimensions. In a small room they sit far apart, so some notes boom and others vanish, usually somewhere between 20 and 300 Hz. Corner bass traps are the standard fix. Use thick broadband traps of 4 inches or more, because thin panels do little in the bass.
For voiceover alone, bass traps are the second purchase after panels at the mic. They matter more if you sing, record a guitar or mix music in the room.
Step 5: Build your own panels
DIY panels use the same material as the commercial ones.
You need: rigid mineral wool such as Rockwool, or rigid fiberglass such as Owens Corning 703, a light wood frame, breathable fabric and a staple gun.
1. Choose the material. Rigid slabs of roughly 40 to 60 kg/m³ (2.5 to 3.75 lb/ft³) work for broadband panels. Owens Corning 703 is 3 lb/ft³. Soft insulation batts slump and aren't suitable.
2. Pick the thickness. Use 2 inches for mids and highs and 4 inches to reach lower.
3. Build a frame about as deep as the slab, then fit the slab inside.
4. Wrap it in breathable fabric such as cotton, linen or speaker cloth. Hold a layer to your mouth and breathe through it. If you can't, sound won't pass through it either. Avoid vinyl and rubber backing.
5. Hang the panels at your marked reflection points.
Safety. Cut the slabs outdoors or in a ventilated space and wear a dust mask, gloves, long sleeves and eye protection. Wrap each panel fully so fibers don't shed. Fiberglass is itchier to handle and mineral wool crumbles less, so check each product's safety sheet.
Rockwool Safe'n'Sound in the 3-inch size was about $91 for a 12-pack of 16-1/4 by 48 inch batts at Home Depot at the time of writing. Check the density before you use it as a bass trap, because it's a lighter product than rigid board.
Step 6: Cheap tricks and what they really do
Blankets. Heavy moving blankets hung in pleats at the sides and behind you can soak up some reflections, though sources disagree on how well. They aren't an acoustic product.
A closet. A closet full of clothes is a popular booth. It absorbs the highest frequencies and gives a dry sound, so treat it as a fallback.
Furniture. A bed, a bookcase, a rug and curtains all add absorption or scattering.
Foam. Foam alone can leave a booth dead in the highs and boomy in the low mids, which sounds oppressive.
What to buy
Prices come from retailer pages and change often, so check before you order.
Product | What it does | Price |
|---|---|---|
sE Electronics Reflexion Filter Pro | Treats the area around the mic | $199 to $209 |
Primacoustic VoxGuard VU | A small vocal shield | about $128 to $147 |
Primacoustic London 8 kit | 12 panels for about 100 sq ft, thin | $390 to $450 |
GIK acoustic panels | Broadband panels | from $64 |
GIK bass trap panels | Corner and wall bass trapping | from $119 |
GIK TriTrap | Corner bass trap | $199 |
GIK Portable Isolation Booth | Portable vocal booth | $499.99 |
A reflection filter treats the space behind and beside the mic and does nothing for the rest of the room.
How much to spend
These tiers are our own rule of thumb, not an industry standard.
Under $100. Blankets or a closet, a rug, a close mic position and the noise fixes below.
About $100 to $300. DIY 2-inch panels at the reflection points and behind the talker, or one reflection filter.
About $300 to $600. 4-inch panels plus corner traps, or a starter kit.
More than that. Bigger bass trapping, a booth and a measurement microphone.
Stop when the clap decays quickly, the voice test no longer sounds hollow and further changes stop improving your before-and-after recordings.
Cut the noise at the source
Treatment can't quiet the world outside. Switch off fans, the air conditioner, the fridge and spinning drives during takes, move the computer away from the mic and close the windows. Record at quiet times of day. Real soundproofing needs mass, decoupling and sealed air gaps, which is a different project from acoustic treatment.
Common mistakes
Covering the walls in thin foam or egg cartons and expecting bass control.
Buying foam to block outside noise.
Over-deadening the room until it sounds boomy and oppressive.
Recording in the middle of the room or in a corner.
Raising the gain instead of moving closer.
Wrapping panels in fabric that isn't breathable.
Chasing an RT60 number from a phone app.
Frequently asked questions
How do I treat a small room for recording?
Absorb the early reflections at the mic, trap the bass in the corners and cut noise at its source. Start with 2-inch absorbers on the side walls and behind the talker, then add thicker corner traps if the low end sounds boomy.
Do I need bass traps for voiceover?
Not at first. Panels at the reflection points do more for a close-miked voice, and bass traps matter more for singing, guitar and music mixing.
Does acoustic foam work for recording?
Thin foam helps only with high frequencies. Sound on Sound says 2-inch foam works above roughly 2 to 3 kHz and 4-inch foam above about 1 kHz, so it leaves the midrange and bass untreated.
What's the best material for DIY acoustic panels?
Rigid mineral wool or rigid fiberglass at 2 to 4 inches thick, with a density of roughly 40 to 60 kg/m³. Rockwool and Owens Corning 703 are the common choices, and soft batts aren't.
Is treating a room the same as soundproofing it?
No. Treatment controls reflections inside the room, and soundproofing needs mass, decoupling and sealed gaps to keep sound from passing through walls.
How can I tell when I've done enough?
Clap again and run the voice test. If the decay is short, the voice no longer sounds hollow and further changes don't improve your recordings, stop.